teanoise71

How to Replace a Kia Sportage Replacement Key For a variety of Kia models, the key contains the keyless entry system that is built into the key. This key usually resembles a remote control and can be changed with a new one from an Kia dealer or a locksmith. Key fobs might stop working due to a variety of reasons, including an empty coin battery, worn buttons signals, water damage, signal interference and a faulty receiver module. Here are some tips to assist you in getting your Kia key fob that is a replacement for the sportage again. How to replace the remote key or smart key? The battery in your Kia's intelligent key will eventually need be replaced, whether it is a remote key that starts with a push button or a normal metal key that doesn't contain a transponder. This is especially relevant if your car displays a message that the remote or smart key has a low battery. It's an easy process. To replace the battery in the keyfob, remove your mechanical key from the slit on the back of the fob. Then, push the cover open. A small screw will be in the key fob that holds the battery in its place. Using a small screwdriver, take the screw off and remove the old battery. Then, you can insert the new battery and close the slit inside the key fob. Test the key fob by pressing the lock and unlock buttons. It's okay if the doors lock and unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you need to run errands around Brandon. Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) don't require programming. If you're looking to reprogramme your key, you'll need record the key code number on the key code tag. How do you replace the battery? If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, this is a good indicator that the battery should be replaced. A low battery may also cause other problems like the check engine light coming on or delayed cranking of the engine. Fortunately replacing the battery on the key fob is a relatively simple DIY task that requires only a few tools. Make sure to shut off your vehicle and close all doors prior to starting. Find the small metal or plastic piece that is on the bottom of your key fob and gently jiggle it until the metal key is released. This key can be placed inside the driver door handle to unlock your car. To replace the key fob battery, remove the cover from the back and use a plier bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery, and then align the new battery so that the “+” positive side faces you, while the “–” negative side is facing the fob's metal electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or breaking the contacts made of metal. After you have installed the new battery, turn the key fob on and off in the ignition until the door locks cycle. Then, test your Kia key fob to determine whether it's functioning properly again. How can you replace the smart key? Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key features an embedded mechanical key blade while the standard keyfob does not. Both key fobs come with batteries that will eventually need to be changed. This is a straightforward process which takes just two minutes. Be sure to turn off your Kia and be on a level and well-lit surface prior to you begin. Remember that kia rio key The Key Lab contains tiny pieces that could be thrown off in the event of a mishap. The first step is to find the small release button that is located on the lower backside of the fob. It's either a circular or rectangular slot. Once you press this, the mechanical key blade will come out and you will be able to open the key fob. Once you have the key fob opened and you are able to take out the old battery and replace it. The new battery is a the CR-2032, and it can be bought on the internet or at your local auto parts store. After you've finished you should be able to lock, unlock and start your car with your key fob even if your engine isn't running! How do I replace the mechanical key The Kia keyfob is a great convenience that allows us to lock or unlock our car by simply pressing the button. Like all devices that is used, the Kia key fob can have issues at times. Luckily, there are methods to solve these issues and ensure that our key fobs are in good working order over the long haul. A dead or weak battery is among the most common problems. The fob could be able to stop working altogether or to work intermittently. If this is the issue it is time to replace the battery a new one. If this isn't enough to resolve the issue, try using a standard flathead screwdriver to open the casing of the fob's plastic. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed and replaced, you can replace it with a new one. Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to check that it's functioning properly. If the key fob isn't working, call a dealer or locksmith to solve the issue. To avoid future lockouts, make sure you get an emergency key that can work in all of the door and trunk cylinders.